Product Characteristics
Operating Voltage: DC 12V
Open Lock current: =<1000mA
Steady Current: =<60mA
Memory Capacity: 250 Standard Users
Max. Read Badge
Distance: 15 cm / 6 inch.
RF Badge Type: H4100
Operating Temp: -10 to 70 degree C
14 to 158 degree F
Operating Humidity: 10% - 90%
Dimension: 117x117x21mm

Installation
To install the control unit on wall, first remove the wall mount piece at the back of the control unit.
1) Remove wall mount piece by using finger to pull at the bottom right, then gradually pull out from control unit.
(Remember the top and the bottom)
2) Use included screws and rubber filling plugs to mount the wall mount piece at desire place.

Wiring
According to the marks on the back of control unit, make correct connections to:
+12, GND, -Lock, +Lock, Open(from inside), Open(from inside), Door Bell, Door Bell.
J1 (At right top corner on the right of to two capacitors)
1 2 3
*Jumper on 1,2=Normally Closed
*Jumper on 2,3=Normally Open

Main Connection Array
+12V GND - Lock + Lock - Open from inside + Open from inside - Door Bell + Door Bell

*When the lock is powered from the supply, “- Lock” is connected to PUSH of power supply.

J2 (At left top corner underneath the siren and the relay)
1 2 3

S16(At middle right above the big Atmel IC chip)
1 2 3

Caution!
Before power up, make sure supply voltage is DC 12V and positive/negative polarity.
Keypad protection sensor is located at bottom right. If triggered, siren will short beep continuously.
Before operation, please read the following instruction carefully.

(I)Initialization
1 Make sure power is off, connect pin 2, 3 of S16.
2 Power on. Siren continuously beep. Indicators: power(red),OK(green) and MODE(Orange) all blink.
3 Power off. Power on again, indicators: Power, OK and MODE all blink. Waiting for S16 to change.
4 Remove jumper on pin 2, 3 of S16, and place jumper on pin 1, 2 of S16.
5 Siren loud beep once. Initialization completed. DLC enters normal operation mode.

*Initialization process resets system password to default password: 12345. Other data will not be erased.

(II)Relay output setting
1 When Pin 1,2 of J1 are connected, then “3”,”4” normally open.
2 When Pin 2,3 of J1 are connected, then “3”,”4” normally closed.
3 J2 is the Hi/Lo voltage level selection.

Program the DLC.
“ #”= FUNCTION key. Enter program mode.
a) Press #, POWER/OK/MODE all blink.
b) Enter 5-digit system password, short loud sound. POWER(On),OK(On), MODE(Off).

Note: This DLC supports 3 types of users:
Type 1, use “Badge” to open door;
Type 2, use “Password” to open door; and
Type 3, use “Badge + Password” to open door.
* User number are 4-digits
* System password is 5-digits
* User password is 6-digits

“0”=Add Type 3 User.
a) Press “0”, ? POWER(Off), OK(Off), MODE(On).
b) Enter 4 digit user number, ? OK(On) indicated the entry is valid.
c) Read a Badge to be registered, ? hear a short beep, ? enter 6-digit password, ? hear a long beep, ? POWER(On), OK(Flash once), MODE(On).

“1” Key, modify system password.
a) Press “1”, ? POWER(Off), OK(Off), MODE(On).
c) User enter 5-digit system password (ie 12345), ? entry done, ? beep once,
? POWER(On), OK(Flash once), MODE(On), ? modification success.

Caution: That user must protect the password. Re-enter system programming mode requires password.
If password is forgotten, initialization is required.

“2” key, add Type 1 or Type 2 user.
a) Press “2”, ? POWER(Off), OK(Off), MODE(On).
b) Enter 4-digit user number, ? OK(On), ? code entered valid.
c) Read registered badge /or enter 6-digit user password, ? long beep,
? Power(on), OK(Flash once), MODE(On), ? user logon succeed.

“3” key, delete single user.
a) Press “3”, ? POWER(Off), OK(Off), MODE(On).
b) Read badge to be deleted, or enter 4-digit user number to be deleted, ? long beep,
? POWER(On), OK(Flash once), MODE(On), ? user delete succeed.
“ 4” key, delete all users.
a) Press “4”, ? long beep, ? Power(On), OK(Flash once), Mode(On), ? all user delete succeed.
“ 5” key, modify door open duration.
a) Press “5”, ? POWER(Off), OK(Off), MODE(On).
b) Enter 2-digit door open duration, ? long beep, Power(On), OK(Flash once), MODE(On),
? door operation duration setting completed.
“ 8” key, modify user password.
a) Press “8”, ? Power(Off), OK(Off), MODE(On).
b) Enter 6-digit original password, ? long beep, ? OK(Flash once), enter new password,
? long beep, ? OK(Flash once), ? user password change succeed.

“6” key, exit programming mode.
Long beep, ? POWER(On), OK(Flash once), MODE(Off), ? DLC exits system program mode, ? return to normal operation mode.

During add user process,
If 3 short beep is heard, it means the user has already registered.
If 4 long beeps is heard, it means RAM is full, can’t register any more.
If 5 time two-long-one-short is heard, it means system memory has readwirte error.
If entry error or operation error occurred, 3 long beeps will be heard and DLC will exit to normal operation mode.

Note: This DLC supports 3 types of users:
Type 1, use “Badge” to open door;
Type 2, use “Password” to open door; and
Type 3, use “Badge + Password” to open door.
* When door is opened, Badges can’t be read.
* When type 2 user is entering password, the pad can’t read Badges.

After programming the DLC, enter the normal operation mode,
POWER(On), OK(Off), MODE(Off), The following steps show how to operate:
a) Either hold user Badge closer to the DLC unit or enter continuously the 6-digit user password, long beep, Power(Off), OK(On), door open success; Within preset door open duration, indicators don’t change.
b) If Siren makes 3 short beeps, and POWER continuously flash 3 times, it means the user badge or user password is invalid, door not opened.
c) If an user has set to be “Badge + Password”, after badge is read, if
Badge Valid,
Long beep, OK(Flash) indicating to enter user password; if
Password valid,
long beep, door opens.
Password not valid,
back up one level and wait for valid password again.
Badge not Valid.
Back up one level to normal operation mode and wait for valid badge.

End.